Re: iTools 6.x and PHP 4.3.x

[eyang@xxxxxxxxx (Eric Yang)]

Yes, make sure mod_ssl module is unloaded in Apache Module Configuration.

regards,
Eric

On Tuesday, July 29, 2003, at 09:48 AM, Dan Tappin wrote:

> Hi Eric,
>
> So all I would need to do is disable SSL on the iTools 6.5.x system 
> (simply though the iTools web interface) and the 4.3.2 PHP should > 
> work?
>
> Thanks,
>
> Dan
>
> On Tuesday, July 29, 2003, at 10:40  AM, Eric Yang wrote:
>
> > This could work, if iTools 6.5.x runs without SSL and Entropy PHP 4.3.2.
> > So there is no conflict of loading expats (XML library) between the 
> > two modules.
> >
> > regards,
> > Eric
> >
> > On Tuesday, July 29, 2003, at 07:32 AM, Dan Tappin wrote:
> >
> > > So are you saying that you currently have iTools 6.5.x AND the 
> > > Entropy PHP 4.3.2 rev5 installed and working?
> > >
> > > Dan
> > >
> > > On Monday, July 28, 2003, at 04:20  PM, Alexei Zoubov wrote:
> > >
> > > > On Friday, July 25, 2003, at 10:39 AM, Eric Yang wrote:
> > > >
> > > > > There are some confusions that might need to be cleared up. 
> > > > > iTools 6.5.x would overwrite the default Apache.  Therefore, 
> > > > > System Preference and other utilities could control the states 
> > > > > of the webserver.  However, iTools 7 is independent from the 
> > > > > default Apache, therefore System Preference and other utilities 
> > > > > are required to have WebServer shut off in order to run iTools 
> > > > > 7.  Therefore, where you hear iTools doesn't mess with default 
> > > > > Apache that only applies to iTools 7.  (Uninstall iTools 6.5.x 
> > > > > will restore your apache to the default Apple Apache).
> > > > >
> > > > > For PHP 4.3.x package, the entropy's PHP has expats library 
> > > > > (XML) compiled in as an static library, and iTools 6.5 has 
> > > > > compiled expats statically for mod_ssl.  Therefore it causes 
> > > > > conflict and unable to load entropy's PHP library with iTools 
> > > > > 6.5.  I would recommend to use iTools PHP package unless your 
> > > > > PHP program only works with PHP 4.3.x, then you will have to 
> > > > > follow this paper and compile PHP manually.
> > > > >
> > > > > http://www.tenon.com/support/itools6/osx/phpbuild.shtml
> > > > >
> > > > > Hope this helps.
> > > > >
> > > > > regards,
> > > > > Eric
> > > >
> > > > I've installed entropy PHP 4.3.2 package with iTools 6.5.7 and 
> > > > until now didn't have any problems at all.
> > > >
> > > > I have a lot of programs already that require PHP 4.3.2 and if 
> > > > pressed for the choice - I'd better go of iTools.
> > > >
> > > > Alexei
> > > >
> > > > ---------
> > > > Tenon Intersystems' iTools Mailing List
> > > > To unsubscribe: send mail to itools-request@xxxxxxxxxxxxxxx
> > > > with the body only containing: unsubscribe
> > > > Find the searchable mailing list archives at:
> > > > http://itools.blackpepper.co.nz/
> > >
> > > ---------
> > > Tenon Intersystems' iTools Mailing List
> > > To unsubscribe: send mail to itools-request@xxxxxxxxxxxxxxx
> > > with the body only containing: unsubscribe
> > > Find the searchable mailing list archives at:
> > > http://itools.blackpepper.co.nz/
> >
> > ---------
> > Tenon Intersystems' iTools Mailing List
> > To unsubscribe: send mail to itools-request@xxxxxxxxxxxxxxx
> > with the body only containing: unsubscribe
> > Find the searchable mailing list archives at:
> > http://itools.blackpepper.co.nz/
>
> ---------
> Tenon Intersystems' iTools Mailing List
> To unsubscribe: send mail to itools-request@xxxxxxxxxxxxxxx
> with the body only containing: unsubscribe
> Find the searchable mailing list archives at:
> http://itools.blackpepper.co.nz/

---------
Tenon Intersystems' iTools Mailing List
To unsubscribe: send mail to itools-request@xxxxxxxxxxxxxxx
with the body only containing: unsubscribe
Find the searchable mailing list archives at:
http://itools.blackpepper.co.nz/